Drip Edge Installation

September 30, 2019

Without a drip edge water may end up beneath the shingles and may cause damage to various parts of the home. The roof leg should extend a minimum of 2 back onto the roof sheathing.

Drip Edge And Ice Barrier Membrane Jlc Online

Drip edge is metal flashing installed at the edges of the roof.

Drip edge installation. Protecting house overall integrity. To install drip edge properly start on the eaves. Slip the wide flat flange of the material all the way under the first course of roof shingles as illustrated.

Be sure to tuck the drip edge under the starter strip and felt paper. But how to install drip edge on a shed roof. Secure the drip edge with roofing cement.

To install a drip edge on a newly constructed roof or on a re-roofing job attach the drip edge along the roofs eaves first. You may need to nail through. When the gap enables movement such as a water stream the deck board will be soaked with moisture.

This is Important to Protect Damage to your Fascia Soffits RaftersTools Supplies Tin Sni. The asphalt shingles can become very brittle during cold weather so youll have to wait until a warm day to remove the eave stripping. Set the drip edge according to so it will align to prevent running water into the gutter.

Next on how to install drip edge on the shed roof is. A drip edge should be placed on the whole perimeter of the roof especially the corners as much as possible. Drip edge installation is also preventing movement between the deck board and fascia.

This is how it can become moldy over time. Drive the nail through the drip edge into the roof surface not through the fascia. Install rake drip edge over the felt.

Start from the eaves to install the drip edge. In this video I just show a quick install of some drip edging and how to cut corners. The flashing can block the stream before it reaches the deck board.

Slide the corner tight to the fascia. Make sure rake edge overlaps. Start the installation at the lower edge of the roof and work your way up toward the peak.

Drip edge installation is a straightforward process following these steps. Make sure to support the long end of the cut if you let it fall after cutting it will bend down and kink the drip edge. If it doesnt pull the drip edge out slightly from under the shingles.

As always thanks for watching. Position the drip edge flange on roof edge. The tip that has flare or flange must face away from the roof and point down.

Installing Drip Edge on your Roof. How to Install a Drip Edge. Install eave drip edge by nailing it to the sheathing.

Drip edge is installed along the roof rakes and eaves to shed water away from the edge. How to Install Drip Edge Flashing to a New Roof. Extend drip edge an inch at each end.

With Without Rain Gutters. Lift the shingles and slide the top flange of the drip edge underneath. While the vertical leg should be placed 14 12 away from the fascia.

Drip edge should be below the underlayment at the eaves and above the underlayment on the rakes. They have a small metal flange that is bent away from the fascia board. It flashes the natural point of separation where the roof deck fascia and rafter tail meet.

Drip edges are metal sheets usually shaped like an L installed at the edge of the roof. Make sure the corner is tight and that the bottom edge is tight to the fascia before nailing off the drip edge. As long as you follow these guidelines you can put the drip edge on after the shingles.

Catch you on the next one. Nail every 12 or less. Rake drip edge overlaps the eave drip edge.

However it can be installed at any time. Begin at the corner of an eave where it meets the next eave or a gable rake. Tom Silva starts off his roofing lesson with the apprentices by stressing the.

To properly install an EDCO style D drip edge use the following steps. Also called drip edge flashing or D-metal they serve a vital function by directing water away from the fascia and into the gutter. The causeway connecting the house to the new garagein-law suite needs a roof.

Tack the edge in place with a roofing nail every foot or so. Make sure the outer edge extends over the gutter. Usually the drip edge is replaced when the new shingles are installed.

They are non-corrosive and non-staining so your roofing system is kept looking good and stable. Place a nail at one end then the other. Install the drip edge on the eaves first.

Measure how far the top of the drip extends past the front face usually 34 or somewhere thereabouts and allow the first.

Drip Edge How To Install One On Your Roof This Old House